Course catalogue

Når kurset er fullført, skal deltakerene være i stand til å klargjøre livbåten, organisere ombordstigning, låre og frigjøre båten, manøvrere og lede operasjonen av livbåten på vannet. 

Regelverk / ansvarsforhold 

Utsetning- systemer for skip og rigg 

Nødkommunikasjon og aktuelt utstyr 

Utstyr i båt og flåte 

Livreddende førstehjelp 

Prosedyrer / alarminstruks 

Kommandoforhold / samarbeid 

Personlig vern og utstyr 

Praktisk øvelse under aktuelle båttype 

Opphold i båt 

Berge opp folk fra sjøen 

Snu en kantret redningsflåte iført redningsvest

Førstehjelp

LEARNING OBJECTIVES

This course is specifically designed for training future DPO’s on board a large number of offshore vessels.

The course aim to provide the candidates with knowledge and skills as preparation for DNV DPO Advanced Operations exams and certification.

By the end of course the students shall have:

• Acquired a thorough knowledge of the various types of DP operations such as ROV operations, cable laying pipe laying, trenching, dredging and rock-dumping
• The capability to operate the DP in the various modes associated with such operations, i.e. joystick,  auto pos mode, autotrack mode and follow target mode
• Recognize when environmental conditions or system failure  requires DPO to take action to avoid hazardous situations
• The  ability to carry out such operations according to existing operational guidelines and checklists
• The ability  to demonstrate good personal attitudes towards safety in operating DP vessels according to best practice in the industry

CONTENT

Planning,  briefing and de-briefing of various field exercises according to the existing guidelines, regulations, and industry standards. Repetition of necessary DP theory to close any knowledge gap the students may have in these subjects.

LEARNING PROCESS

All DP  exercises will be carried out on a full scale DNV GL Approved DP Class A simulator, using vessels that are equipped according to DP class 2 and 3. The participants will perform both surface and subsea  operations, utilizing the following DP modes: Joystick, Autoposition, Autotrack and Follow target functionalities.

SPECIAL INFORMATION

• DNV GL, Standard for Certification no. 0023
• DNV GL, Standard for Certification no. 0008
• DNV GL, RP-0007
• NMA 201209765-4/813.4.
• GOMO, Guidelines for offshore marine operations, Supply and Rig Move Operations and other relevant guidelines such as IMCA M-117 and other IMCA guidelines

A level test will be conducted before commencing the course.

CERTIFICATE

Certification of attendance will be issued upon successful completion of the course.

LEARNING OBJECTIVES

After the course, the successful participants are able to:

• Define the principles of DP
• Recognise the component parts of a DP system
• Understand the relationship between vessel movement  position reference systems, sensors, computers propulsion units and feedback
• Understand the concept of redundancy
• Understand the DP modes of control
• Describe the operation of sensors and common position reference systems
• Describe propulsion units, types and configurations
• Understand power supply, redundancy and management
• Practice communication and watch handover procedures

CONTENT

• Definition of DP, elements of the DP system, DP systems redundancy, and Class Requirements
• Functions of the DP system, and DP principles
• Different types of DP vessels and DP operations, sensors and use of sensor inputs
• Introduction to position reference systems and the DP system’s use of position measurements
• Vessel capability, DP consequence analysis and DP capability analysis
• Thrusters and manoeuvring systems
• Power systems and Blackout Prevention
• Operational procedures for DP operation, and procedures for operating the DP system
• Study of DP incidents
• Principal use of the DP system

LEARNING PROCESS

The training will be a combination of theoretical lessons and practical exercises. During the course each participant will have his own operator station with generic DP software.

SPECIAL INFORMATION

The DP Induction course is the first phase of the Nautical Institute (NI) DP Operator Certification Scheme. The course participants will be issued with the NI Dynamic Positioning Operator’s Log Book upon successful completion of the DP Induction Course.

This course is according to the system specific competence requirements in IMO STCW Regulations I/14 1.5, Part A-I/14 2.1.1, part B V/f 6 and IMCA M117.

CERTIFICATE

A certificate accreditated by the Nautical Institute will be issued on succcessful completion of the course.

Hensikt:

Målsetting med opplæring er at den som gis opplæring tilegner seg tilstrekkelig kunnskap om metoder for å lede og veilede løfteoperasjoner slik at de blir forskriftmessig utført.

Opplæringen gir også kunnskap om farer forbundet med løfteoperasjoner samt bruk av risikokartlegging.

Kurset gir deltakere kunnskap til å kunne utøve overordnet operasjonell ledelse av løfteoperasjoner. Med det menes å kunne planlegge, risikokartlegge og evaluere, samt forebygge ulykker. Videre vil deltaker også tilegne seg kunnskaper om å gjøre rede for materialhåndteringsplan, oppbevaring og bruk av utstyr.

Målsetting med opplæring er at den som gis opplæring tilegner seg tilstrekkelig kunnskap om metoder for å lede og veilede løfteoperasjoner slik at de blir forskriftmessig utført.

Innhold:

• Krav og ansvar til rollen operasjonelt ansvarlig

• Lover, forskrifter, standarder og retningslinjer som gjelder vedr. bruk av løfteutstyr

• Overordnet operasjonell ledelse av løfteoperasjoner

• Helhetlig planlegging av løfteoperasjoner

• Risikokartlegging

• Identifisering av og etablering av barrierer. Gjennomføring og evaluering av en løfteoperasjon

• Informasjonsutveksling

• Krav for oppbevaring av løst løfteutstyr

• Krav for ulike typer løfteutstyr

• Krav til fadder, praksis og sensor

• Avsluttende prøve

Objective: The purpose of the training is to provide users of work equipment mentioned in § 10-1 and 10-3 in «Regulations on the performance of work» (no. 1357), a good general basic training in the safe use of work equipment, so that accidents and accidents in connection with use is avoided.

The authorities set requirements for basic safety certification of persons who are to drive forklifts, mass transfer machines and cranes. The requirements include both theoretical and practical training. To complete the common theory, one must take and pass a theoretical exam.

Module 1.1 Working environment, responsibilities and consequences are common to machine, forklift and crane. If you can document that you have module 1.1 from before that is not older than 3 years, you can start right on module 2.3.

Content:

- Laws and regulations
- Working environment, responsibilities, and consequences
- Environmental
- Safety regulations
- Dangerous goods, marking and handling

Objective: The aim of the training is that theoretical and practical knowledge about fall protection and the correct use of rescue equipment, rescue of free-hanging persons, rescue of personnel over open sea, tank, stretcher transport, descent and treatment of personnel after fall accident is refreshed and repeated.

The training is adapted for personnel who are part of fall protection / rescue teams on board an installation. Participants must gain expertise in risk assessment, rescue (equipment and methods) and first aid.

Covers repetition requirements every 2nd year in accordance with NOG 113 and SFS.

Content:

Introduction
Regulations
Review of accidents and incidents
The rescue service
Equipment
Routines when working at height
Risk assessment
Management, site of injury
Stress and stress management
Hanging trauma, CPR
Rescue drills
Evaluation

Kurset er i henhold til NS-EN- 1591-4. Kurset øker kompetansen og gir grunnleggende kunnskaper innen forberedelse, planlegging, utførelse og dokumentering av arbeid med boltetrekking av flensforbindelser på trykksatte systemer.

Kurset dekker følgende tabeller i NS-EN 1591-4:

Tabell 1: Foundation level training matrix.

Tabell 2: Training matrix for hydraulic tension tightening.

Tabell 3: Training matrix for hydraulic torque tightening.

Tabell 6: Training matrix for bolt load determination after assembly.

Tabell 7: Training matrix for compact flanges.

Tabell 8: Training matrix for clamp connectors

Tabell 9: Training matrix for special connector/flanges

Hensikt: Hensikten med kurset å forhindre skade på personell, miljø og utstyr. Dette kan forebygges ved å styrke kompetansen og øke forståelsen hos den enkelte.

This course is only available in Norwegian.

The course is in accordance with NS-EN 1591-4 and undergoes the same course content as an ordinary four-day course but without the use of hydraulic torque tool and tensioning tools.

The use of a mechanical torque wrench is the main focus but also a review of procedures, flanges, gaskets, practical tasks and more.

The course ends with a theoretical and practical exam. If passed, the approval is valid for 5 years.

Courses are conducted in Stavanger or Bergen
and is carried out on request.

Course price NOK 5300, - pr. participant.

Hensikt: Grunnleggende overlevelsestrening for offshore vindindustri. 

Ved gjennomføring av Global Wind Organization (GWO) Basic Safety Training (BST) vil delegatene ha en bevissthet om farene som oppstår når de arbeider i vind-industrien og hvordan man kontrollerer og reduserer disse farene.

Kursdeltakerne vil få (repetert) kunnskap og ferdigheter til å anerkjenne fordeler og begrensninger knyttet til livreddende utstyr og PVU samt korrekt bruk av dette i forbindelse med offshore vind. 

Hensikten med kurset er å gi deltakerne kunnskaper/oppfriskning om livreddende utstyr, GMDSS og SAR utstyr, hvordan en kollektivt kan øke sjansen til overlevelse i en nødsituasjon, hvordan entre og forlate vindturbiner, samt evakuering i nødsituasjoner. 

Kurset dekker krav til opplæring av personell og repetisjonskurs både land- og havvind iht:

- Global Wind Organization (GWO)

- Arbeidstilsynet (Forskrifter)


Kompetanse for «Sea Survival» skal vedlikeholdes iht. retningslinje i GWO standarden. Det skal gjennomføres repetisjonskurs hvert 2. år.

This course is only available in Norwegian.

The Norwegian authorities require that employees who use lifts (personnel lifts) must be able to document practical and theoretical training in their use. The employer is responsible for ensuring that employees receive the necessary training. (“Regulations regarding the execution of work” no. 1357, section 10-2 Requirements regarding documented safety training in the use of work equipment.) The course provides a basic theoretical and practical introduction to the safe use of lifts (personnel lifts). A certificate of competence is issued to participants in order to fulfil the legislation’s documentation requirements.
Objective: To provide course participants with increased knowledge and awareness of safety measures in order to avoid injuries and accidents at the workplace. 

The following topics are covered:
– Assembly
– Operation
– User qualities
– Areas of use
– Maintenance and control
– Safe use and servicing
– Classes A, B and C
– Accidents
– Legislation and regulations